Possibilité de financement en magasin avec Flexiti - Détails
Voir tous les produits
AMERICAN STANDARD
Baignoire rectangulaire en acrylique blanc 34 po x 60 po avec vidange à droite
N° d'article 00535065
N° de produit 000419051
N° de modèle 2647.102.011
Format 60x30"
Rabais de
105,80
$
jusqu'au 20 nov. 2024
423
,
20
Chacun
529,00 $
Rabais de
105,80
$
jusqu'au 20 nov. 2024
Cet article n'est pas offert pour le moment, mais il peut être commandé en visitant le magasin sélectionné.
Ajouter au panier
Retour sans problème
90 jours pour retourner ou échanger dans son état et son emballage original.
Lire la politique de retour
Garantie
Limitée à vie
Ajouter au panier
Description
- Le plancher antidérapant de la baignoire assure la sécurité lors de l'entrée et de la sortie
- baignoire à jupe de 60 po L x 33,75 po L x 17 po H
- La baignoire Arctic white de la collection Saver est l'endroit idéal pour se détendre
- La forme ovale ou rectangulaire ajoute une touche d'élégance à votre salle de bains
- La surface acrylique brillante est résistante aux rayures et facile à nettoyer
- Drainage compatible : 1640305
- La vidange correspond à la sortie sur le côté droit
- Le tablier incurvé offre plus d'espace de bain dans le même espace qu'une baignoire standard
Caractéristiques
Intensité de courant
0
Garantie de base sur la main-d'oeuvre (mois)
0
Capacité de la baignoire
1 personne,
Longueur réelle (cm)
152,4
Longueur nominale (cm)
152,4
Longueur réelle (mm)
1524,0
Longueur nominale (mm)
1524,0
Hauteur réelle (po)
17
Volume d'eau (l)
170.343
Poids de l'article assemblé (kg)
27,216
Largeur nominale (po)
30
Largeur réelle (po)
30
Hauteur réelle (cm)
43,18
Hauteur réelle (mm)
431,8
Poids de l'article assemblé (lb)
60
Longueur réelle (po)
60
Longueur nominale (po)
60
Largeur nominale (cm)
76,2
Largeur nominale (mm)
762,0
Largeur réelle (cm)
76,2
Largeur réelle (mm)
762,0
Garantie de base sur les pièces (mois)
9999
Type de baignoire
Alcôve
Famille de couleurs/finis
Blanc
Garantie
Limitée à vie
À porte
Non
Conforme aux exigences de l'ADA
Non
Orientation du jet réglable
Non
Flux réglable
Non
Douche de plain-pied
Non
Robinet de baignoire inclus
Non
Tension de la baignoire
S.O.
Nom de la collection
Saver
Type de contours de baignoire
Séparé,
Drain compatible
S.O.
Type de commandes
S.O.
Contour de bain assorti
2649BW.011
Jupe amovible
Non
Sens d'ouverture de la porte
S.O.
Drain inclus
Non
Emplacement du drain
Droite
Pour usage commercial
Non
Convient aux maisons mobiles
Non
Autoportant
S.O.
Douchette incluse
Non
Famille de couleur de la quincaillerie
Blanc
Fini de la quincaillerie
S.O.
Chauffage inclus
Non
Siège intégré
Non
Éclairé
Non
Matériau
Acrylique
Débit maximal (douche à main)
S.O.
Nombre d'injecteurs d'air
0
Nombre de jets
0
Coussin inclus
Non
Produit exclusif
S.O.
Télécommande incluse
Non
Forme
Rectangulaire
Design à jupe
Non
Compatibilité avec les appareils intelligents
Non
Profondeur de cuve (cm)
28,575
Profondeur de cuve (po)
11.25
Profondeur de cuve (mm)
285,75
Toilette incluse
Non
Porte de baignoire incluse
Non
Couleur/fini du fabricant
Arctique
Volume d'eau (gal)
45
Mise en garde concernant le produit
Images à titre de référence seulement, accessoires non inclus
Profil du seuil
Seuil bas
Type de baignoire thérapeutique
Bain de trempage
Baignoire rectangulaire en acrylique blanc 34 po x 60 po avec vidange à droite est évalué
de
5 de
11.
Rated 5 de
5
de
Big Danny par
I really love the curved shower unit
I really love the idea of the curved shower unit. It gives me more space inside the shower when showering. It gives the bathroom a luxurious look
Date de publication: 2020-03-02
Rated 5 de
5
de
Ellsworth par
Great tub, great price.
The tub was easily installed by our plumber without encountering any issues. Thetub could have had more fiberglass backing on the inside. Some areas did not have any on it and you could see light through the acrylic. I was assured by customer service that this would in no way affect the structure. I attached standard insulation to the tub before installing and this resulted in retaining heat and coolness in the water for an extended time. We are very happy with our purchase and at the price paid it is an exceptional value considering American Standard is a leader in this field.
Date de publication: 2019-09-02
Rated 5 de
5
de
SRobinson par
OUTSTANDING TUB
This is a big beautiful tub! It is very easy to clean and keeps its shine. It is the best tub to soak in with a lot of room.
Date de publication: 2019-08-16
Rated 2 de
5
de
Fk American standard par
Would not recommend
Drain is way way way off so your basic drain kit won’t fit. You will have to make your own pvc overflow and drain with a flexible fitting
Date de publication: 2018-05-31
Rated 5 de
5
de
Garyzilla par
Great Tub, More room!
Great quality tub and wall kit. Makes our small bathroom feel bigger, I have back problems and need to soak and this IS the nicest tub I've found to do so. Id recommend a couple extra steps to install, originally got the tub and didn't want to do tile or go with a flimsy surround, the one on display was cheesy. After unboxing the tub wall kit in the isle and taking measurements I decided that with some extra steps I could sturdy it up.
Set the tub in a bed of mortar.
You'll have to move the tub fill pipe up (plumber needed or experienced DIYer, we had to gut everything due to mold anyway) otherwise where the tub fill spout meets the curved part of the tub wall it wont sit flush, or all the way against the panel tight.
I spray foam filled the tub wall shelves completely and trimmed excess, no flexing now.
I added backing for future grab bars if needed, and between studs everywhere the tub wall flange would be.
Vapor barrier on all walls.
Attached 1/4" hardi board on all walls 1" past all tub wall flange areas.
I glued the heck out of the panels to 1/4" hardie board with Loctite tub wall adhesive, it's one of the few that actually say it works on cement boards, as well as being waterproof. 1/4" beads every 6-8" grid pattern on anything that touched the hardie board, the back of each shelf where it would contact hardi, and the tub deck where the panels sit and each joint where the panels meet each other and the screw flange to the wall board. 4 tubes worth!
Then when the adhevive is fully cured , caulk all joints with white silicone, the sticky stuff.
Very important to level your tub deck during install, front to back side to side each end, the tub wall kits have some play built in for walls that wing out or in, in the front or back, but the tub deck must be level to get your wall kit joints tight. That is a good reason to use the mortar base, take your time then and get it level, screw the flange to the studs by just resting the screw on top of the tub flange and tightening until the head is tight to the tub flange, I used some washers on a couple that needed it. Now let the mortar set.
When its time , get in the tub (put a towel down) and move around looking for squeaks, adjust/add screws as necessary, I had to use a shim in one spot.
On the wall kit flange I predrilled and used a countersink, barely , where I screwed to the studs so It wouldn't crack the plastic.
You could use 1/4 sheetrock as a backer also but get the green kind.
We've had it about 6 months and it cleans easy with dawn, used carnuba wax once to get the water spots off (we have hard water), it seems to hold up well, my son plays with all matter of things in there and I haven't noticed a scratch. It's a great product but like anything, needs installed right. Kinda like my 20 year roof that lasted 2 years (roof leaks, siding and sheetrock damage inside), was done by the same handyman that "reused" a toilet wax ring when doing tile in the bathroom just prior to us purchasing the house (toilet leaked under the tile every time we flushed for about a year before we noticed "a smell")....
I wouldn't just screw the top flange of the tub wall to a stud and call it good, that leaves the rest of the panel, especially at the bottom, all floppy. It has nothing to attach to except at the top, so think of it as a shower curtain. If its floppy and flexy your silicone caulk joints will surely fail, if you don't use backing and the tub adhesive all that holds (or doubtfully will) the wall panel to the tub at the bottom is the silicone. Find an intelligent installer, or be one. I'm a cabinet installer/carpenter.
Date de publication: 2017-05-06
Rated 5 de
5
de
J R H par
Nice and wide without using as much space.
I bought this for our main upstairs bathroom. I could have fit a regular 34" tub in the pre-existing alcove, but i wanted to have a clean tile bullnose all the way to the floor so I opted for a 32" with the bowed front. The tub is more than enough room for just about anyone. The installation was a breeze and I picked it up myself with a normal sized SUV. The tub wasn't heavy in the slightest. I bought the deep soak drain with he tub and together my wife is in heaven. Great product at a spectacular price. Most stores had these in stock in my area so it was a same day pick up.
Date de publication: 2017-01-31
Rated 5 de
5
de
Unclexxxxxx par
Love it !
We had this tub installed in a remodel to our bathroom and within 2 weeks it had a crack, so we called american standard and they took control of this very quick. They called a tub repair co and the company called and we set a date and time for the repair.We could not tell where the crack had been without knowing beforehand.
Date de publication: 2016-01-02
Rated 3 de
5
de
user7568993 par
You have to be creative to get this in correctly
The other reviewers are correct. This tub has a MAJOR design flaw in that the exterior drain flange is cut at the wrong angle. If you use a traditional drain kit, you will run into nothing but issues and it will leak... no matter how many gaskets you add.
The fix: When plumbing out the drain, get the PVC fittings without all of the pipes. This will usually consist of a drain fitting (90 degree), overflow fitting and overflow cover. Next, you will then get the PVC pipes to build a proper 1.5" trap. After you have these parts, you will then get a 1.5" fernco flexible drain fitting. This fitting is different than most other Fernco's as it is grey in color and far more flexible. Get enough 1.5" PVC pipe to make your stub ends. I ended up getting a 3 foot span so I had extra to work with.
Once you have all of the parts, you will want to install the 90 degree exterior drain fitting directly to the flange WITHOUT anything connected to it. Get it sealed nice and snug. After this is complete, build the rest of the parts on this. The Fernco will compensate for the angle issue and you will get a good seal.
Outside of this issue, the tub is great. The only complaint I have is the glass is a little thin on the sides. I am surprised American Standard would slip this bad when it comes to QA on such a critical part of the tub.
Date de publication: 2014-07-16